Salt Content Analysis with ASTM Methods D3230 for Crude Oil
The salt content is one of the most important parameters of quality control. code oil, especially before crude oil enters the processing stage at the refinery. The existence of inorganic salt in the oil crude can increase the risk of corrosion on process equipment, building deposits, and disruption of processing systems if not properly controlled. Therefore, Salt Content Analysis is required to determine the concentration of salt in crude oil as part of a quality evaluation of raw materials.
The PT Hidea Power supports laboratory analysis needs for petroleum products and oil & gas industrial needs. The test results can be used as support data in the oil cruise quality evaluation, desalting process control, as well as monitoring the conformity of raw materials before resolving.
Top Salt Content Analysis for Oil & Gas Industries
For the Oil & Gas sector, specifically production, processing, and resolving of crude oil, salts control is an important aspect of keeping operational reliability. The Salt Content testing provides information about the concentration of salt in oil crudes so that potential problems during processing can be evaluated earlier.
Some of the major benefits of Salt Content testing include:
- Crude Oil Quality Evaluation
Testing Salt Content helps determine the rate of salt content in crude oil as one of the parameters of characterization and the quality control of raw refinery materials. - Corrosion Control
High levels of salt can increase the potential of corrosive compounds during processing. Analytic data can be used as one of the considerations in risk control corrosion on refinery equipment. - Support
The test results can be used to evaluate the content of salt before and after the process of desalting, so it helps monitor effectiveness process salts in crude oil. - Monitoring Default Content Refinery Quality
Salt concentration information can be a support data to evaluate the consistency of the oil cruil before entering the distillation and continued processing process.
Salt Content Test Parameters Specification
The testing of Salt Content is based on ASTM D3230 to estimate the concentration of salt in the oil crude through the measurement of electrical conductivity. This method responds to the existence of the common chloride salt component found in crude oil, like sodium chloride, calcium chloride, and magnesium chloride.
Here are the general specs on Salt Content testing:
| Testing Parameters | Specification |
|---|---|
| Parameter Name | Salt Content |
| Testing Method | ASTM D3230 |
| Analysis Principle | Electrometric Method |
| Size Principle | Electrical conductivity measurement |
| Sample Type | Crude Oil |
| Result Unit | mg / kg or PTB (Pounds per Thousand Barreels) |
| Testing Destination | Estimating salts based on sample conductivity response |
Test Method ASTM D3230 - Electrometric Method
ASTM D3230 It's a standard method of determining salt content in oil crudes using electrometric techniques. The test principle is based on measuring the electrical conductivity of the sample mix and solvent solution prepared by method procedures.
In general, the principle of testing includes the following stages:
- Sample Preparation - The oil crude samples prepared and mobilized according to the need for testing procedures.
- Sample Mixer - Samples mixed with solvent and solution systems specified in ASTM method D3230.
- Conductivity Measurement - The sample alloy is analyzed using the electrodes to get electrical conductivity response.
- Calibration and Evaluation - The measurement response is compared to the appropriate calibration curve.
- Results - Salt concentration estimated and reported in mg / kg or PTB units as required reporting.
The test results from ASTM D3230 are an estimate of the contents of salt based on an electrometric response, not a separate quantum identification for any type of ion. The existence of other conductive materials can also affect measurement results.
Salt Content Analysis in the Crude Oil Desalting Process
Process crude oil dessalting It's a process stage that aims to reduce salt and water in crude oil before entering the distillation process. Uncontrolled salt content can contribute to corrosion, deposit formation, and disruption to process equipment.
The Salt Content test can support evaluation of desalting processes through some of the following aspects:
- Evaluation of the Salt Concourse Before Desalting - Knowing the initial conditions of the oil cruil before the salt reduction process is carried out.
- Monitor Processing Results - Compare the test results before and after the process to evaluate the changes in the salt content.
- Feedstock Quality Control - Provides data analysis as part of a quality evaluation of oil cruil before entering advanced processing units.
Thus, Salt Content Analysis results can become one of the support parameters in the control of the raw materials and operational evaluation of refinery.
Power Hidea Salt Content Analysis Service
As a lab focuses on the Oil & Gas sector and petroleum analysis, PT Hidea Core It supports laboratory testing needs for the characterization of oil crudes and petroleum products. The testing of Salt Content is one of the parameters that can be consulted to support raw oil quality evaluations as well as industrial process control needs.
For more information about the availability of ASTM D3230 testing, sample types, sample volume needs, time-making, and price deals, please contact our lab team.
PT Hidea Core
High Idoas. Solution.
The area of Industrial and Tekno Park, 18 Block J1, BSD, Kel.
Email: labservices@hidea.id
WhatsApp: + 62 877-6494-5736
