Inspection: checking the condition and weight of traded goods at loading, discharge port or during trans-shipment, control quantity and quality and meet all relevant regulations
Verification: ensure your products comply with global and local standards and regulations and covers the entire supply chain
Testing: Hidea provide testing services and integrated it with Engineering to came up with the solution for the customer problem or if the customer need a more analysis related to failure analysis therefore we can provide special analysis such as corrosion and scaling analysis in their production process.
Commercial survey, inspection, sampling and testing services with supporting Certificates and other relevant documentation, including, but not limited to the following:
- Hold and Tank Cleanliness/Condition Surveys – vessel’s cargo worthiness, including hold and tank condition and cleanliness, and the general suitability to load a particular cargo.
- Vessels of On/Off Surveys – vessel’s hold condition and/or bunker on board at time of “on/off hire.”
- Compliance Surveys – verifying the vessel’s suitability to carry cargoes governed by rules or codes, such as grain, bulk cargoes, timber deck cargoes and hazardous goods; and the practical application of local laws and customs of the trade.
- Cargo Pre-Loading Surveys – to measure and calculate the cargo’s volume for freight payment and stowage purposes, and to verify its condition by recording all visible damage before shipment or at the warehouse or dock for insurance purposes, carriers and freight forwarders.
- Loading, Handling and Stowage Advice – including stability and stress calculations; advice on draft and trim; safe carriage and discharge; to assure the effectiveness of securing; and for recommending and supervising loading, stowage, lashing, blocking and bracing to ensure the safe carriage of the cargoes.
- Grain Stability Separations and Stress Calculation – assisting master in the loading planning and/or calculation to best meet the code.
- Heavy-Lift and Project Cargo Surveys – cargo condition, handling, stowage and lashing before and during loading are mostly done on behalf of shippers, underwriters, carriers and freight forwarders.
- Pre-Shipment Surveys – surveys of break-bulk cargo, especially newsprint, wood-pulp and project cargoes to ensure that bills of lading and mate’s receipts accurately note the apparent condition of cargo when it is loaded, and to comment on the water tightness, condition and ventilation of the vessel’s holds.
- Out-turn Surveys – surveys of break-bulk cargo, especially steel, on arrival at the discharge port, to establish condition and any damages or shift of cargo that may have occurred during the voyage. This survey often requires Silver Nitrate testing for chloride residues.
- Draft Surveys – surveys to determine the quantity of a bulk cargo loaded or discharged by reading the vessel’s drafts, measuring the ballast water, fuel and diesel oil and other liquids on board, and calculating the final quantity by using the vessel’s approved dead-weight scales and tank tables, etc.
- Dead-freight Surveys – to determine by measurement the amount of cargo a vessel could have loaded if all the available space was utilised. This is to determine the loss of freight due to short shipment of cargo.
- Hatch Sealing – to ensure that no contamination or loss of cargo occurs during passage or stopover in other Ports prior to final destination.
- Damage Surveys – investigation of cargo damage or loss claims on behalf of P&I Clubs, carriers, shippers, consignee, etc. to determine possible cause and extent of any damage that may have occurred during shipment and to assist in mitigating further losses.
- Stevedore and Terminal Damage – the investigation and survey of damage to vessels, terminal equipment, containers, cargo, cargo hoses, etc. that is alleged to have occurred as the result of handling the equipment, cargo, etc.
Automation and control systems play a vital role across different sectors; from power plant, oil and gas, chemicals, cement, to food and beverage, water treatment, and others. BPI offers its clients advanced automation and control technologies, such as:
- Programmable Logic Control
- Distributed Control System
- Substation Automation System
- SCADA and Tele-control System
- Conveying System
- Pick and Place System
- Robotic System
Management information systems (MIS) in industrial business consist of an information technology and networking system. Hence, it is Hidea’s goal to develop advanced IT automation in order to find alternative and reliable solutions at a minimum cost. BPI is able to develop a complete networking system by effectively using:
- Fiber-optic technology
- Advance database programming
- Application software
- OPC interfacing communication for advanced IT automation
- Laboratory management Information systems (LIMS)
- Controlling from quotation up until invoicing process
- Storage Management Systems.
Hidea’s services are designed to offer comprehensive and integrative solutions for clients with the possibility to request for standard and / or tailored services, such as installation, testing and commissioning of control system, etc.